|
● TECHNICAL CHARACTERISTICS
■ Efective travel .............................................. X= 530 mm.
■ Efective travel ........................................... Y= 1.000 mm.
■ Efective travel .............................................. Z= 160 mm.
● Possibility of paths in the axis
Z ............................................. from 75mm. up to 475mm.
● Ball screws in the 3 axes.
● Height from table to bridge ................................... 190 mm.
● Alternating Current (A.C.) Brushless Servomotors
with absolute encoder.
● Safety micros, end of journey.
● Prismatic type sliding guides, with
continuous recirculation of balls.
● Protection bellows on all guides.
● HEAD
■ High speed head.
■ Start - Stop, manual and automatic through control.
■ Number of revolutions:
▪ Minimum ........................................... 11.000 r.p.m.
▪ Maximum .......................................... 25.000 r.p.m.
■ Max capacity of tool............................................... 6 mm.
■ Power .................................................................. 500 W.
■ Voltage ................................................................. 220 V.
■ Possibility of installing diamond
for engraving.............................................................YES.
● WORK TABLE
■ Table dimensions ................................ 750 x 1.350 mm.
■ Number of "T" slots .................................................. 15.
■ Distance between slots ..................................... 50 mm.
■ Table to floor height ......................................... 960 mm.
■ Maximum weight on the table .......................... 100 kg.
● HIGH SPEED CONTROL SYSTEM
■ BECKHOFF numerical control CP2216 controlled by PC and integrated PLC and software TwinCAT 3 NC I.
■ TwinCAT 3 NC I, 3 interpolated main axes, up to 5 auxiliaries per group, one group per channel and up to 31 channels.
■ 2 Ethernet ports with 2 x 10/100/1000.
■ 15.6” Multi-touch monitor, 1366 x 768 pixel display.
■ 1 RS232 Serial Port and 4 USB 2.0 ports.
■ UPS Uninterruptible Power Supply, integrated into 24 V power, without batteries.
■ 1 DVI-D port occupied by the monitor and 1 free DVI-I port.
■ 1 free slot for Mini PCI cards.
■ 2½” Solid State Hard Drive, 320 GB.
■ Open architecture and programmable CNC control software.
■ Minimum cycle time of 50 microseconds.
■ Zero point offsets, tool offsets, M and H functions, mathematical functions, parameter / variable programming, user macros, spindle and auxiliary functions, zero point offsets, tool functions, etc.
■ Comprehensive geometry functions: linear, circular and helical interpolation in principal planes and freely definable levels, max. 32 axis interpolation path per channel (optional), look-ahead function.
● DRIVES
■ Brushless Alternating Current (AC.) Servomotors with 18-bit resolution multiturn "absolute encoder".
● RESOLUTION
■ Resolution X,Y,Z .......................................... 0,001 mm.
● SPEEDS
■ Maximum speed ........................................... 10 m/mm.
● MACHINE DIMENSIONS
■ Maximum dimensions ........ 1.230 x 1.720 x 1.800 mm.
● WEIGHTS
■ Gross weight ................................................. 850 kg
■ Net weight ..................................................... 600 kg
● PACKAGING
■ Dimensions ........................ 1.400 x 1.900 x 1.950 mm.
■ Volume ............................................................. 5,2 m3.
● Standard EQUIPMENT INCLUDED (in each machine)
1 Beckhoff numerical control
1 High speed head from 11,000 to 25,000 r.p.m.
1 Tool holder nut.
1 Ø6mm clamp.
1 Set of fastening flanges.
1 Service key set.
1 Toolbox.
● OPTIONAL EQUIPMENT
■ 500 W Head Clamps, from Ø 1 to 6 mm.
■ 1,050 W. power head, clamp up to Ø 8 mm.
■ 1,050 W head clamp, from Ø 1 to 8 mm
■ High frequency motorized head of 3 HP
■ Automatic tool change
■ Electronic approach steering wheel
■ Integral fairing with safety lock
■ Chip protector
■ Automatic reset device
■ Laser Probe for Calibration.
■ Laser for Tool Measurement
■ LED lighting lamps
■ MQL Lubrication Equipment
■ Oil mist cooling equipment
■ CAD/CAM engraving 2 ½D, NasCAD 2000 © Plus
■ CAD/CAM of 3D artistic engraving, ModelArt3D.net
■ CAD/CAM for photo engraving PhotoNAS
■ ELECTRONIC DIVIDER - 4th AXIS A. *
* For roller machining.
■ Personal computer for design, complete
■ Vacuum clamp tables
■ Special jaws for irregular pieces
■ Precision jaws, ground
■ Eccentric clamping flanges + ruler
■ Magnifying and Measuring Loupes
■ USB magnifying microscope
■ Diamond tools
■ Diamond Set for Marking
■ Thread chuck for quick change collet
■ Automatic Threader
|
